ENEnglish CN简体中文 BDবাংলাদেশ BGБългарски HRHrvatski CZČesky DKDansk NLNederland EOEsperanto SISlovenski PHFilipino FISuomi FRFrançais DEDeutsch GRΕλλάδα ILישראל INइंडिया HUMagyarország ISÍsland IDIndonesia SVNIrlanda ITItalia JP日本語 SVNSovensko AMՀայաստան KR한국 KGKyrgyz LVLatvian LTLithuanian MKMacedonian MYМалайская MTMaltese NPनेपाल NONorge IRایران KGPolska PTPortugal RORomânia RUРоссийская BABosanski SISlovenian BYБеларус ESEspaña SESverige TJТочик THประเทศไทย TRTürk AZAzərbaycan VNViệt Nam GBCymraeg TAதமிழ் SKSlovak ALShqiptare EUEuskara LALatinus ZAAfrikaans

xmjy@baduseal.com

+86-592-5100981

Language

ENEnglish CN简体中文 BDবাংলাদেশ BGБългарски HRHrvatski CZČesky DKDansk NLNederland EOEsperanto SISlovenski PHFilipino FISuomi FRFrançais DEDeutsch GRΕλλάδα ILישראל INइंडिया HUMagyarország ISÍsland IDIndonesia SVNIrlanda ITItalia JP日本語 SVNSovensko AMՀայաստան KR한국 KGKyrgyz LVLatvian LTLithuanian MKMacedonian MYМалайская MTMaltese NPनेपाल NONorge IRایران KGPolska PTPortugal RORomânia RUРоссийская BABosanski SISlovenian BYБеларус ESEspaña SESverige TJТочик THประเทศไทย TRTürk AZAzərbaycan VNViệt Nam GBCymraeg TAதமிழ் SKSlovak ALShqiptare EUEuskara LALatinus ZAAfrikaans

Home / News / FKM O-Rings

Customized FKM o-rings introduces the knowledge of O-ring replacement

2022-06-13

Do you understand the knowledge of O-ring replacement? Today, thecustomized FKM o-ringseditor will take you to a brief understanding.
1. During use, once wear occurs, an all-round inspection should be carried out, and the wear situation should be analyzed. If the wear is not very serious, the sealing ring can be cleaned and used again.
2. If the sealing ring is seriously worn and can no longer be used, then it is necessary to carry out the disassembly and replacement work immediately. Before the replacement, it is necessary to find a matching sealing ring, and it is necessary to process a concave inside the sealing ring. The grooves, the depth and spacing of the grooves should be controlled in place.

customized FKM o-rings
3. When installing a new sealing ring, it should be embedded in the groove. Note that the installation part should be clamped tightly, and it should not be stuck or clamped too tightly.
4. After the new sealing ring is installed, the burrs on the edge of the groove should be cleaned to ensure that the edge is smooth. If the seal ring is found to be out of groove, it should be reinstalled.
5. After dismantling and replacing the sealing ring, before the official use, it should be checked whether the installation is in place to see if there is any medium leakage.
The above is the customized FKM o-rings editor: a brief introduction to the knowledge of O-ring replacement.

back

One stop manufacturing service provider for seals

Contact Us

xmjy@baduseal.com

+86-592-5100981

No. 40, Huliyuan, Industrial Concentration Zone, Tong'an District, Xiamen City

Copyright © 2021 Xiamen Badu Seal Co., Ltd. All rights reserved.闽ICP备15005984号-1